1.x Output overload | UC3 |
2.x Usage error | UC3 |
3.x Calibrating tool not in position | UC3 |
4.x Conveyor OHC open | UC3 |
5.x Flow rate too low / Water pump switched off | UC3 |
6.x EMERGENCY STOP: control panel | UC3 |
7.x EMERGENCY STOP: feeder/machine | UC3 |
8.x EMERGENCY STOP: downstream | UC3 |
10.x EMERGENCY STOP: upstream | UC3 |
12.x External machine OFF downstream | UC3 |
13.x External machine OFF upstream | UC3 |
14.x Conveyor: drive fault | UC3 |
15.x Profiler drive: fault | UC3 |
16.x Wire chopper drive: fault | UC3 |
17.x Feeder magazine open | UC3 |
19.x Greasing not completed successfully. Check for blocked tubes. | UC3 |
20.x Double-sheet too late | UC3 |
22.x Min. sheet stack | UC3 |
23.x Overcurrent release | UC3 |
24.x Overcurrent release: Unisoud/Pulsar | UC3 |
25.x Multiple misfeeds | UC3 |
26.x Oiling not completed successfully. Check for blocked tubes | UC3 |
27.x Transport motor: OHC too hot | UC3 |
28.x Transport motor: SC (support conveyor) too hot | UC3 |
29.x Wire chopper motor too hot | UC3 |
30.x Control cabinet/autotransformer too hot | UC3 |
31.x Cooling water / DISCON too hot | UC3 |
32.x Profiler motor too hot | UC3 |
33.x Unisoud/Pulsar converter too hot | UC3 |
34.x Unisoud/Pulsar power supply too hot | UC3 |
35.x Welding transformer too hot | UC3 |
36.x Usage error | UC3 |
36.x Resolver | UC3 |
36.x Overvoltage | UC3 |
36.x Overcurrent | UC3 |
36.x Velocity error too large | UC3 |
36.x Power supply | UC3 |
36.x Communication | UC3 |
36.x Optional PCB | UC3 |
36.x Position error too large | UC3 |
36.x General drive fault | UC3 |
36.x Master resolver | UC3 |
36.x Current regulator | UC3 |
36.x Address selection | UC3 |
36.x Sensor defective | UC3 |
36.x Brake error | UC3 |
36.x Clutch not engaged | UC3 |
36.x Clutch disengaged | UC3 |
36.x Clutch not released | UC3 |
38.x Power supply fault | UC3 |
39.x Profiler not started | UC3 |
40.x Protective door: feeder right open | UC3 |
41.x Protective door: feeder left open | UC3 |
42.x Protective device: front | UC3 |
43.x Protective door: wire chopper open | UC3 |
44.x Protective door: wire run-in open | UC3 |
45.x Welding roller lifted | UC3 |
46.x Rollformer open | UC3 |
49.x Conveyor 1: not in position | UC3 |
50.x Conveyor 2 not in position | UC3 |
51.x Unisoud/Pulsar converter: fault | UC3 |
52.x Unisoud/Pulsar power supply fault or Control cabinet door open | UC3 |
54.x Wire break at wire chopper | UC3 |
55.x Wire break in wire loop | UC3 |
56.x Wire knot monitoring | UC3 |
57.x Wire magazine is empty | UC3 |
58.x Wire traction too low | UC3 |
59.x Mounted transport module is incorrect | UC3 |
60.x Protective door: conveyor drive open | UC3 |
61.x Double-sheet sensor is defective | UC3 |
63.x Rollformer: drive fault | UC3 |
67.x Burner fault | UC3 |
68.x Burner not lit | UC3 |
69.x Gas pressure too low | UC3 |
70.x EMERGENCY STOP: Oven | UC3 |
71.x Protective device: rear open | UC3 |
75.x Oven temperature too high | UC3 |
76.x Oven not operational | UC3 |
77.x External line stop | UC3 |
78.x External line stop downstream | UC3 |
79.x Oven startup failure | UC3 |
81.x Single sheet too late | UC3 |
82.x Rounding station open | UC3 |
83.x External EMERGENCY STOP | UC3 |
84.x Can-body guide channel not in position | UC3 |
85.x Belt tension too low/broken | UC3 |
87.x Monitor channel not responding | UC3 |
88.x STW: press not ready | UC3 |
89.x Too many faulty can-bodies | UC3 |
91.x Overcurrent release | UC3 |
92.x All can bodies ejected | UC3 |
93.x Can body was not ejected / diverted | UC3 |
94.x Can-body jam | UC3 |
95.x STW: Tongue strip not ready | UC3 |
96.x Eject synchronisation lost | UC3 |
99.x Monitor: rear of can not found | UC3 |
101.x Front of can-body series was not found | UC3 |
102.x Leading end of can bodies shifted | UC3 |
103.x Monitor: too many samples | UC3 |
104.x Not enough can-bodies | UC3 |
105.x Monitor: too few samples | UC3 |
106.x Setup failed | UC3 |
107.x Oven: water level/flow rate too low | UC3 |
108.x Double-sheet container not in position | UC3 |
109.x Roller head/Wire drive: fault | UC3 |
110.x Conveyor drive: fault | UC3 |
111.x Conveyor 1: clutch disengaged | UC3 |
112.x Conveyor 3: clutch disengaged | UC3 |
113.x Rollformer motor overheated | UC3 |
114.x Corona: overcurrent fault | UC3 |
115.x Corona: Measured current out of working range | UC3 |
116.x Corona: wiring fault | UC3 |
117.x OHC is open | UC3 |
118.x No powder | UC3 |
120.x Cleaning fault | UC3 |
121.x Sieve housing open | UC3 |
125.x PRC not in position | UC3 |
126.x Conveyor 3 bottom disengaged | UC3 |
127.x Plunger: fault | UC3 |
128.x Unable to eject can body | UC3 |
129.x Inadequate suction | UC3 |
131.x Trailing end too early | UC3 |
132.x Trailing end too late | UC3 |
139.x Suction hood not in position | UC3 |
141.x Machine clock lost | UC3 |
142.x Protective door: open | UC3 |
147.x STW: sheet guide 5 is open | UC3 |
148.x STW: sheet guide 6 is open | UC3 |
149.x STW: sheet guide 7 is open | UC3 |
152.x Lacquer: initial fill timeout exceeded | UC3 |
153.x Basin not filled | UC3 |
154.x Basin: insufficient lacquer flow | UC3 |
156.x STW: transport conveyor scoring station open | UC3 |
157.x STW: acceleration conveyor is open | UC3 |
158.x STW: sheet reject is defective | UC3 |
160.x Conveyor 2: clutch disengaged | UC3 |
164.x STW: Protective door right open | UC3 |
165.x STW: Protective door left open | UC3 |
167.x STW: tongue wheel not in position / tongue wheel upper position | UC3 |
168.x STW: tongue wheel locked | UC3 |
172.x STW: Sheet guide 1/2 is open | UC3 |
173.x STW: Sheet guide 2 is open | UC3 |
175.x STW: Sheet guide 3 is open | UC3 |
176.x Double sheet detected | UC3 |
183.x Protective door: welding transformer open | UC3 |
185.x EMERGENCY STOP: Machine | UC3 |
188.x STW: Sheet guide 4 is open | UC3 |
190.x Too many deflected sheets | UC3 |
193.x Feeder overload | UC3 |
194.x Sheet missing in rollformer | UC3 |
195.x Oil level too low | UC3 |
197.x Protective door: welding rollers open | UC3 |
199.x EMERGENCY STOP: line | UC3 |
200.x Unisoud/Pulsar: Measured current regulator deviation | UC3 |
202.x Double sheet deflector is defective | UC3 |
204.x First can-body contaminated | UC3 |
205.x Protective door: wire loop open | UC3 |
240.x Sensor defective | UC3 |
240.x Sensor defective | UC3 |
240.4 Sensor defective | UC3 |
240.5 Sensor defective | UC3 |
240.6 Sensor defective | UC3 |
240.12 Sensor defective | UC3 |
240.12 Sensor defective | UC3 |
240.13 Sensor defective | UC3 |
240.13 Sensor defective | UC3 |
240.14 Sensor defective | UC3 |
240.19 Sensor defective | UC3 |
240.25 Sensor defective | UC3 |
240.25 Sensor defective | UC3 |
240.32 Sensor defective | UC3 |
240.32 Sensor defective | UC3 |
240.33 Sensor defective | UC3 |
240.33 Sensor defective | UC3 |
252.x Setting of key switches inadmissible | UC3 |
252.x Selection of Mode/Function are invalid | UC3 |
300.x Safety relay monitoring | UC3 |
305.x Bad weld profilee | UC3 |
306.x Weld profile too complex | UC3 |
308.x Monitor Channel failed | UC3 |
313.x Too many missing can-bodies | UC3 |
314.x Too many can-bodies on ejector conveyor | UC3 |
320.x Setup successful | UC3 |
327.x Can-body jam | UC3 |
329.x Sheet missing in rollformer | UC3 |
330.x Double-sheet: sensor voltage | UC3 |
334.x Setup is required | UC3 |
337.x Monitor: no limits available | UC3 |
340.x Monitor: invalid setup data | UC3 |
341.x Setup is requirede | UC3 |
342.x Monitor: speed changed | UC3 |
343.x Monitor: Machine clock has changed | UC3 |
344.x Monitor: defective hardware | UC3 |
345.x Analog board defective | UC3 |
347.x Stationary transport / Sensor defective | UC3 |
354.x Outside seam coating system is not ready | UC3 |
355.x Inside seam coating or powder system is not ready | UC3 |
361.x Insufficient powder level | UC3 |
363.x Oven is not ready | UC3 |
365.x Powder test mode is on | UC3 |
366.x Can-body jam | UC3 |
367.x EAC/DCS can-body jam | UC3 |
368.x Elevator/Erector fault | UC3 |
370.x Vacuum not released | UC3 |
374.x LARC: conveyor stopped too early | UC3 |
376.x Combustion air pressure too low | UC3 |
377.x Process air pressure too low | UC3 |
378.x Motor too hot | UC3 |
378.x Servo amplifier too hot | UC3 |
379.x Loader is above top | UC3 |
381.x External machine stop | UC3 |
414.x Powder: RS232 communication fault | UC3 |
415.x Powder: incorrect firmware version | UC3 |
417.x Powder monitor: signal too high | UC3 |
418.x Powder monitor: Sensor or background contaminated | UC3 |
419.x Powder monitor: signal too low | UC3 |
420.x Powder monitor: machine clock unstable | UC3 |
498.x 24V power supply fault | UC3 |
421.x Powder: insufficient startup voltage | UC3 |
422.x Powder: insufficient startup current | UC3 |
423.x Powder: Measured current out of working range | UC3 |
424.x Powder monitor: Wrong reference data | UC3 |
426.x SOUVIS: Not responding | UC3 |
444.x SOUVIS: No confirmation | UC3 |
479.x Suction unit not ready | UC3 |
498.x 24V power supply fault | UC3 |
491.x Shuttle 1: rear end position | UC3 |
493.x Shuttle 1: front end position | UC3 |
497.x Overcurrent release | UC3 |
500.x Line: Control cabinet too hot | UC3 |
507.x Compressed air too low / outside pressure range | UC3 |
521.x Drive fault / overcurrent release | UC3 |
526.x Battery backup check: | UC3 |
545.x Wire break at profiler | UC3 |
547.x CamProfile Download in Progress | UC3 |
548.x Powder monitor: bad status | UC3 |
549.x Powder: bad packet status | UC3 |
550.x Powder: bad read access | UC3 |
551.x Powder: bad data access | UC3 |
559.x Waiting for Press | UC3 |
565.x Sheet Stack not in Position | UC3 |
566.x Powder monitor: reference reflector not applied | UC3 |
567.x Powder monitor: calibration required | UC3 |
572.x Powder: firmware not loaded | UC3 |
574.x Powder: download in progress | UC3 |
575.x Move loader to bottom position | UC3 |
576.x Pack aligner not at back position | UC3 |
577.x Pack not aligned | UC3 |
579.x Pack feeder protective door open | UC3 |
581.x SOUVIS | UC3 |
582.x Inside spray: lacquer flow not ok | UC3 |
584.x Sensor defective | UC3 |
587.x Drive fault | UC3 |
588.x Analog values too small | UC3 |
589.x Min. sheet stack | UC3 |
590.x Energy channel is switched off | UC3 |
591.x No analog signal from OCR unit | UC3 |
596.x Line: Turn table inlet conveyor has stopped | UC3 |
597.x Line: Can jam on erector | UC3 |
598.x Line: Can jam on turner | UC3 |
600.x Electromagnetic disturbance | UC3 |
604.x Line: In manual mode | UC3 |
605.x All can bodies ejected | UC3 |
606.x DC Fuse broken | UC3 |
606.x DC voltage asymmetric | UC3 |
606.x DC voltage shorted | UC3 |
606.x DC voltage too high | UC3 |
606.x DC voltage too low | UC3 |
606.x Dig.Outp.X8 overcurrent | UC3 |
606.x Driver board1 not found | UC3 |
606.x Driver board2 not found | UC3 |
606.x Driver board3 not found | UC3 |
606.x Driver board4 not found | UC3 |
606.x Gap too small | UC3 |
606.x Host read > | UC3 |
606.x Host write > | UC3 |
606.x I2C > | UC3 |
606.x Initialisation lost | UC3 |
606.x Main contactor remains off | UC3 |
606.x Main contactor remains on | UC3 |
606.x Main voltage too high | UC3 |
606.x Main voltage too low | UC3 |
606.x No Regulator Identification | UC3 |
606.x Parameter limitation | UC3 |
606.x Relay driver X9 > | UC3 |
606.x SPI > | UC3 |
606.x Unit1 IGBT HBA shorted | UC3 |
606.x Unit1 IGBT HBB shorted | UC3 |
606.x Unit1 Overcurrent | UC3 |
606.x Unit2 IGBT HBA shorted | UC3 |
606.x Unit2 IGBT HBB shorted | UC3 |
606.x Unit2 Overcurrent | UC3 |
606.x Unit2 Rms Current Deviation | UC3 |
606.x Unit3 IGBT HBA shorted | UC3 |
606.x Unit3 IGBT HBB shorted | UC3 |
606.x Unit3 Overcurrent | UC3 |
606.x Unit3 Rms Current Deviation | UC3 |
606.x Unit4 IGBT HBA shorted | UC3 |
606.x Unit4 IGBT HBB shorted | UC3 |
606.x Unit4 Overcurrent | UC3 |
606.x Unit4 Rms Current Deviation | UC3 |
606.x Weld Synchronization missing | UC3 |
607.x Unit1 Fan not running | UC3 |
607.x Unit1 IGBT too hot | UC3 |
607.x Unit1 too hot | UC3 |
607.x Unit2 IGBT too hot | UC3 |
607.x Unit2 too hot | UC3 |
607.x Unit3 IGBT too hot | UC3 |
607.x Unit3 too hot | UC3 |
607.x Unit4 IGBT too hot | UC3 |
607.x Unit4 too hot | UC3 |
607.x Unit2 Fan not running | UC3 |
607.x Unit3 Fan not running | UC3 |
607.x Unit4 Fan not running | UC3 |
608.x SOUVIS | UC3 |
609.x Machine clock lost | UC3 |
612.x Protective door: feeder open | UC3 |
613.x Roller head not lifted | UC3 |
618.x Grease level too low | UC3 |
619.x Handwheel engaged | UC3 |
620.x Positioning pin inserted | UC3 |
621.x Feeder magazine open | UC3 |
622.x Scoring station open | UC3 |
623.x Sucker rod disengaged | UC3 |
624.x Rollformer safety clutch | UC3 |
625.x Air pressure guiding tool too low | UC3 |
626.x Ejector: Twin can detected | UC3 |
627.x Feeder: vacuum off delay too long | UC3 |
628.x Monitor: First can travelling time out of tolerance | UC3 |
629.x Pulsar: Contamination detected | UC3 |
606.x Bad weld profile | UC3 |
606.x 24V_BLK1 X9 missing | UC3 |
606.x Contamination | UC3 |
630.x Brake > | UC3 |
630.x Clutch disengaged | UC3 |
630.x Clutch not engaged | UC3 |
630.x Clutch not released | UC3 |
630.x Communication | UC3 |
630.x DC voltage too low | UC3 |
630.x Drive defective | UC3 |
630.x Drive missing | UC3 |
630.x Drive overloaded | UC3 |
630.x Resolver | UC3 |
630.x Hardware enable missing | UC3 |
630.x Motor defective / wiring wrong | UC3 |
630.x Not in position | UC3 |
630.x Output overload | UC3 |
630.x Position > too large | UC3 |
630.x Position Limit reached | UC3 |
630.x Power Input out of tolerance | UC3 |
630.x Encoder | UC3 |
630.x Unknown > | UC3 |
630.x System > | UC3 |
630.x Sensors/limit switch | UC3 |
630.x Power supply fault | UC3 |
630.x Sensor defective | UC3 |
630.x Usage > | UC3 |
630.x Wire loop too short | UC3 |
630.x Wire break | UC3 |
631.x Motor too hot | UC3 |
631.x Servo amplifier too hot | UC3 |
631.x Wire traction unstable | UC3 |
632.x Function affected by contamination | UC3 |
636.x Can-body jam | UC3 |
637.x Line: Downstream/Bodyformer has stopped | UC3 |
638.x Transport 1 clamp open | UC3 |
639.x STW: tongue rejection failed | UC3 |
647.x Deviation too large | UC3 |
647.x Deviation zero | UC3 |
647.x Inductance too large | UC3 |
647.x No results | UC3 |
647.x Weld circuit open | UC3 |
648.x STW: Too many missing tongues | UC3 |
655.x Software too old | UC3 |
657.x Move loader to bottom position | UC3 |
660.x Blank stack robot above rollformer | UC3 |
661.x Sensor defective | UC3 |
662.x Outside spray: Insufficient lacquer flow | UC3 |
663.x ARS/SRM: Out of Measuring Range | UC3 |
664.x Oven not heat up | UC3 |
665.x ARS/SRM: Measuring plate shorted | UC3 |
666.x Monitor: Too many measured samples during setup | UC3 |
667.x Protective door/Emergency Stop monitoring fault | UC3 |
668.x Protective door: rollformer open | UC3 |
668.x Protective door: can guide channel is open | UC3 |
668.x Protective door: can guide channel is open | UC3 |
668.x Protective door: rollformer open | UC3 |
670.x Sorter: Tube is missing at end of transout | UC3 |
671.x Powder monitor: Calibration out of tolerance | UC3 |
672.x Can-body height | UC3 |
673.x Eject station: Unstable can detection | UC3 |
677.x Sheet Stack not in Position | UC3 |
679.x Transport1 brake is active | UC3 |
680.x Plate roll at weld station is blocked | UC3 |
681.x Output overload | UC3 |
681.x Overtemperature: Inductor 1 | UC3 |
681.x Overtemperature: Inductor 2 | UC3 |
681.x System > | UC3 |
681.x Internal supply | UC3 |
681.x DC voltage too low | UC3 |
681.x Overtemperature: Generator | UC3 |
681.x Fan failure | UC3 |
681.x Electromagnetic disturbance | UC3 |
681.x General fault | UC3 |
681.x Analog values too large | UC3 |
681.x Overvoltage | UC3 |
681.x current regulator failure | UC3 |
681.x Overcurrent | UC3 |
681.x Hardware enable missing | UC3 |
681.x short-circuit | UC3 |
681.x Current out of Tolerance | UC3 |
682.x Rounding speed has changed | UC3 |
683.x Pulsar: Power supply switch on timeout | UC3 |
685.x Acopos drive enable missing | UC3 |
686.x Seam cooling unit not ready | UC3 |
687.x conveyor 3 bottom | UC3 |
688.x Two hand button activation: operation failed | UC3 |
689.x Feeder: Too many sheets out of timing tolerance | UC3 |
690.x Output: powered with external voltage | UC3 |
691.x Powder: CPF silo sensor contaminated | UC3 |
692.x Power supply missing | UC3 |
693.x Power supply jumper wrong | UC3 |
694.x Node hardware defective | UC3 |
695.x Energy channel is switched off | UC3 |
696.x Energy: quality factor | UC3 |
697.x Eject all is ON (Push button) | UC3 |
698.x Can-body jam | UC3 |
699.x Output overload | UC3 |
699.x Overtemperature: Inductor 1 | UC3 |
699.x Overtemperature: Inductor 2 | UC3 |
699.x System > | UC3 |
699.x Internal supply | UC3 |
699.x DC voltage too low | UC3 |
699.x Overtemperature: Generator | UC3 |
699.x Fan failure | UC3 |
699.x Electromagnetic disturbance | UC3 |
699.x General fault | UC3 |
699.x Analog values too large | UC3 |
699.x Overvoltage | UC3 |
699.x current regulator failure | UC3 |
699.x Overcurrent | UC3 |
699.x Hardware enable missing | UC3 |
699.x short-circuit | UC3 |
699.x Current out of Tolerance | UC3 |
700.x No signal from Encoder | UC3 |
701.x Line control : Linestop to welder | UC3 |
702.x Bodyformer: Welder off | UC3 |
703.x Oven: SCU not ready | UC3 |
704.x Inside: lacquer system fault | UC3 |
705.x Unisoud/Pulsar: Measured current regulator deviation | UC3 |
734.x Heat: Pyrometer is not ready | UC3 |
742.x Guidance not closed | UC3 |
743.x Rollformer open/close: Mechanically locked | UC3 |
744.x Rollformer open/close: Protective door fault | UC3 |
745.x Machine stop extern (energy free) | UC3 |
746.x Machine stop (energy free) | UC3 |
748.x One hand (slow motion): operator failed | UC3 |
749.x Light barrier interrupted | UC3 |
750.x Sensor contaminated | UC3 |
751.x Sensor defective | UC3 |
752.x Sensor defective | UC3 |
753.x Cooling water | UC3 |
754.x Cooling water / DISCON too hot | UC3 |
755.x Air pressure is too high | UC3 |
756.x Lacquer monitor is activated | UC3 |
757.x Wire knot monitoring | UC3 |
758.x Wire magazine is empty | UC3 |
759.x Wrong Hardware | UC3 |
760.x Contamination | UC3 |
761.x Pressure out of tolerance | UC3 |
763.x CANopen: Bus off | UC3 |
764.x Device missing | UC3 |
765.x Drive system startup is in progress | UC3 |
766.x Too many deflected sheets | UC3 |
767.x Insufficient powder level | UC3 |
768.x Line stop | UC3 |
769.x Energy: Short circuit voltage too low | UC3 |
770.x Pressure out of tolerance | UC3 |
771.x Can-body guide channel is not at down position | UC3 |
772.x Outside spray: System not in working position | UC3 |
773.x Emergency: Feedback loop faulty | UC3 |
774.x PNOZ: Fatal > | UC3 |
782.x System is mandatory | UC3 |
783.x Line: Turner outlet jam | UC3 |
784.x Upender can jam | UC3 |
785.x PRC: Lacquer level is too low | UC3 |
786.x Powder: No response | UC3 |
787.x Machine clock unstable | UC3 |
789.x Powder: HVS current too low: wiring fault | UC3 |
790.x Powder: fault | UC3 |
792.x Overtemperature switch | UC3 |
793.x Protective door: water plate open | UC3 |
794.x CAN Bus > | UC3 |
794.x CAN High > | UC3 |
794.x CAN Low > | UC3 |
794.x Resistance too high | UC3 |
794.x Resistance too low | UC3 |
794.x Not allowed on this node | UC3 |
794.x Device defective | UC3 |
794.x Measurement > | UC3 |
796.x PRC: Lacquer level is low | UC3 |
797.x Flow rate too low | UC3 |
798.x Press oven on button to restart burner ignition | UC3 |
799.x Burner control must be reset manually | UC3 |
800.x Oven: Safety combination | UC3 |
801.x Suction hood not in position | UC3 |
802.x Destacker: Double sheet not ejected | UC3 |
803.x Destacker: Additional sheet detected | UC3 |
804.x Destacker: Sheet transport fault | UC3 |
805.x STW: sheet reject is defective | UC3 |
806.x Communication | UC3 |
806.x Drive defective | UC3 |
806.x Measurement > | UC3 |
806.x Width not constant | UC3 |
806.x Width too large | UC3 |
806.x Width too small | UC3 |
807.x Line stop | UC3 |
810.x OSS: Lacquer pressure out of tolerance | UC3 |
815.x Contamination | UC3 |
817.x Can-body jam | UC3 |
818.x Double-sheet container is full | UC3 |
819.x STW Monitor: Too many bad tongue welding cycles. | UC3 |
820.x Burner control could not be reset | UC3 |
821.x Sensor defective | UC3 |
822.x Protective door: Manual feed open / not locked | UC3 |
823.x Pack transfer TP not in safe position | UC3 |
824.x Protective door: Front open / Front left open | UC3 |
825.x Protective door: Front right open | UC3 |
826.x Protective door: Feeder right down open / not locked | UC3 |
827.x Protective door: Feeder right up open / not locked | UC3 |
828.x Protective door: Feeder backside open / not locked | UC3 |
829.x UTC lacquer reservoir empty | UC3 |
830.x UTC lacquer reservoir is filling | UC3 |
834.x Lift table: Palett/Pack incorrect loaded | UC3 |
835.x TP: Rear cover open / not locked | UC3 |
836.x TP: Right cover open / not locked | UC3 |
837.x UTC change empty lacquer tank | UC3 |
838.x Monitor: Input signal out of range | UC3 |
839.x Welder run with batch counter only / Set batch counter! | UC3 |
840.x TP: Rear cover open / not locked | UC3 |
841.x Monitor: Eject logic not started | UC3 |
842.x Line stop | UC3 |
844.x Protective door: Rear open or not acknowledged | UC3 |
845.x Protective door: Rear up open | UC3 |
846.x Loader is above top | UC3 |
847.x EMERGENCY STOP: Whole line | UC3 |
848.x EMERGENCY STOP: External | UC3 |
853.x Discon pump switch off: Circuit 2 too low | UC3 |
854.x Oven: Wait for burner power supply | UC3 |
855.x Line control : Linestop to welder | UC3 |
856.x Flow rate too low / Water pump switched off | UC3 |
857.x Protective door: Manual feed open / not locked | UC3 |
858.x MLC: Downstream demands immediate stop | UC3 |
859.x MLC: Communication to line control missing | UC3 |
859.x MLC: Communication to line control missing | UC3 |
860.x MLC: Communication to line control missing | UC3 |
861.x TP: Rear cover open / not locked | UC3 |
862.x TP: Rear cover open / not locked | UC3 |
863.x TP: Right cover open / not locked | UC3 |
864.x Protective door: Manual feed open / not locked | UC3 |
865.x Energy: Measured current too low | UC3 |
866.x ARS/SRM: Piezo position out of tolerance | UC3 |
867.x MLC: Downstream not ready | UC3 |
871.x Erector DCU: Magnet off time between cans too short | UC3 |
872.x Erector DCU: Magnet driver fault | UC3 |
873.x MLC: Communication to line control missing | UC3 |
874.x Oven not operational | UC3 |
875.x Lacquer temperature out of tolerance | UC3 |
876.x RS 232 communication fault | UC3 |
877.x No power for peltier element | UC3 |
878.x User interface is locked | UC3 |
881.x Pulsar: Too many contamination on short circuit | UC3 |
883.x UTC lacquer reservoir empty | UC3 |
884.x LTC Device status > | UC3 |
885.x MLC: Downstream not ready | UC3 |
886.x LTC maximum temperature exceeded. Check LTC cooling! | UC3 |
887.x STW: Wire threading switch is enabled | UC3 |
888.x Oven: Pyrometer temperature too low | UC3 |
889.x Oven: Pyrometer temperature too low | UC3 |
890.x Oven: Pyrometer not working | UC3 |
891.x Upstream system clutch disengaged | UC3 |
892.x Machine safety stop | UC3 |
893.x Peltier element defective or wiring fault | UC3 |
894.x Machine off | UC3 |
895.x Lacquer monitor: pulse duration too small | UC3 |
896.x Lacquer monitor: pulse duration too small | UC3 |
897.x Oven: Can flow monitoring entry to exit fault | UC3 |
898.x Can body was not ejected / diverted | UC3 |
899.x Stationary transport / Sensor defective | UC3 |
900.x Sensor defective | UC3 |
902.x HvGenerator | UC3 |
902.x Voltage too high | UC3 |
902.x Current too high | UC3 |
902.x Current too low | UC3 |
902.x Current out of range | UC3 |
902.x Resistance too high | UC3 |
902.x Resistance too low | UC3 |
902.x Lifesign > | UC3 |
902.x Internal fault | UC3 |
902.x Serial communication timeout | UC3 |
902.x Wiring fault | UC3 |
902.x Power supply missing | UC3 |
902.x Output current too low | UC3 |
902.x SPI > | UC3 |
902.x Signal invalid | UC3 |
902.x Voltage too low | UC3 |
902.x General fault | UC3 |
903.x Test pulse > | UC3 |
903.x Time discrepancy channel 2 | UC3 |
903.x Time discrepancy channel 1 | UC3 |
903.x Time discrepancy releasing | UC3 |
903.x Short/cross circuit | UC3 |
903.x Lock > | UC3 |
903.x Release > | UC3 |
903.x Hardware > | UC3 |
903.x Release > 2 | UC3 |
904.x Safety not ready | UC3 |
905.x Powder application in cleaning process | UC3 |
908.x Zero position not found | UC3 |
910.x Loader: Sheet stack is empty | UC3 |
913.x Monitor: Feeder ON signal unstable | UC3 |
917.x Too many rejected can-bodies | UC3 |
918.x Oven eject container at oven end is full | UC3 |
919.x Oven target status | UC3 |
920.x Upender: Downline not ready | UC3 |
921.x OHC is open | UC3 |
922.x HvDiagnostics | UC3 |
924.x Energy counter not working | UC3 |
| |
| |