| 1.x Output overload | UC3 |
| 2.x Usage error | UC3 |
| 3.x Calibrating tool not in position | UC3 |
| 4.x Conveyor OHC open | UC3 |
| 5.x Flow rate too low / Water pump switched off | UC3 |
| 6.x EMERGENCY STOP: control panel | UC3 |
| 7.x EMERGENCY STOP: feeder/machine | UC3 |
| 8.x EMERGENCY STOP: downstream | UC3 |
| 10.x EMERGENCY STOP: upstream | UC3 |
| 12.x External machine OFF downstream | UC3 |
| 13.x External machine OFF upstream | UC3 |
| 14.x Conveyor: drive fault | UC3 |
| 15.x Profiler drive: fault | UC3 |
| 16.x Wire chopper drive: fault | UC3 |
| 17.x Feeder magazine open | UC3 |
| 19.x Greasing not completed successfully. Check for blocked tubes. | UC3 |
| 20.x Double-sheet too late | UC3 |
| 22.x Min. sheet stack | UC3 |
| 23.x Overcurrent release | UC3 |
| 24.x Overcurrent release: Unisoud/Pulsar | UC3 |
| 25.x Multiple misfeeds | UC3 |
| 26.x Oiling not completed successfully. Check for blocked tubes | UC3 |
| 27.x Transport motor: OHC too hot | UC3 |
| 28.x Transport motor: SC (support conveyor) too hot | UC3 |
| 29.x Wire chopper motor too hot | UC3 |
| 30.x Control cabinet/autotransformer too hot | UC3 |
| 31.x Cooling water / DISCON too hot | UC3 |
| 32.x Profiler motor too hot | UC3 |
| 33.x Unisoud/Pulsar converter too hot | UC3 |
| 34.x Unisoud/Pulsar power supply too hot | UC3 |
| 35.x Welding transformer too hot | UC3 |
| 36.x Usage error | UC3 |
| 36.x Resolver | UC3 |
| 36.x Overvoltage | UC3 |
| 36.x Overcurrent | UC3 |
| 36.x Velocity error too large | UC3 |
| 36.x Power supply | UC3 |
| 36.x Communication | UC3 |
| 36.x Optional PCB | UC3 |
| 36.x Position error too large | UC3 |
| 36.x General drive fault | UC3 |
| 36.x Master resolver | UC3 |
| 36.x Current regulator | UC3 |
| 36.x Address selection | UC3 |
| 36.x Sensor defective | UC3 |
| 36.x Brake error | UC3 |
| 36.x Clutch not engaged | UC3 |
| 36.x Clutch disengaged | UC3 |
| 36.x Clutch not released | UC3 |
| 38.x Power supply fault | UC3 |
| 39.x Profiler not started | UC3 |
| 40.x Protective door: feeder right open | UC3 |
| 41.x Protective door: feeder left open | UC3 |
| 42.x Protective device: front | UC3 |
| 43.x Protective door: wire chopper open | UC3 |
| 44.x Protective door: wire run-in open | UC3 |
| 45.x Welding roller lifted | UC3 |
| 46.x Rollformer open | UC3 |
| 49.x Conveyor 1: not in position | UC3 |
| 50.x Conveyor 2 not in position | UC3 |
| 51.x Unisoud/Pulsar converter: fault | UC3 |
| 52.x Unisoud/Pulsar power supply fault or Control cabinet door open | UC3 |
| 54.x Wire break at wire chopper | UC3 |
| 55.x Wire break in wire loop | UC3 |
| 56.x Wire knot monitoring | UC3 |
| 57.x Wire magazine is empty | UC3 |
| 58.x Wire traction too low | UC3 |
| 59.x Mounted transport module is incorrect | UC3 |
| 60.x Protective door: conveyor drive open | UC3 |
| 61.x Double-sheet sensor is defective | UC3 |
| 63.x Rollformer: drive fault | UC3 |
| 67.x Burner fault | UC3 |
| 68.x Burner not lit | UC3 |
| 69.x Gas pressure too low | UC3 |
| 70.x EMERGENCY STOP: Oven | UC3 |
| 71.x Protective device: rear open | UC3 |
| 75.x Oven temperature too high | UC3 |
| 76.x Oven not operational | UC3 |
| 77.x External line stop | UC3 |
| 78.x External line stop downstream | UC3 |
| 79.x Oven startup failure | UC3 |
| 81.x Single sheet too late | UC3 |
| 82.x Rounding station open | UC3 |
| 83.x External EMERGENCY STOP | UC3 |
| 84.x Can-body guide channel not in position | UC3 |
| 85.x Belt tension too low/broken | UC3 |
| 87.x Monitor channel not responding | UC3 |
| 88.x STW: press not ready | UC3 |
| 89.x Too many faulty can-bodies | UC3 |
| 91.x Overcurrent release | UC3 |
| 92.x All can bodies ejected | UC3 |
| 93.x Can body was not ejected / diverted | UC3 |
| 94.x Can-body jam | UC3 |
| 95.x STW: Tongue strip not ready | UC3 |
| 96.x Eject synchronisation lost | UC3 |
| 99.x Monitor: rear of can not found | UC3 |
| 101.x Front of can-body series was not found | UC3 |
| 102.x Leading end of can bodies shifted | UC3 |
| 103.x Monitor: too many samples | UC3 |
| 104.x Not enough can-bodies | UC3 |
| 105.x Monitor: too few samples | UC3 |
| 106.x Setup failed | UC3 |
| 107.x Oven: water level/flow rate too low | UC3 |
| 108.x Double-sheet container not in position | UC3 |
| 109.x Roller head/Wire drive: fault | UC3 |
| 110.x Conveyor drive: fault | UC3 |
| 111.x Conveyor 1: clutch disengaged | UC3 |
| 112.x Conveyor 3: clutch disengaged | UC3 |
| 113.x Rollformer motor overheated | UC3 |
| 114.x Corona: overcurrent fault | UC3 |
| 115.x Corona: Measured current out of working range | UC3 |
| 116.x Corona: wiring fault | UC3 |
| 117.x OHC is open | UC3 |
| 118.x No powder | UC3 |
| 120.x Cleaning fault | UC3 |
| 121.x Sieve housing open | UC3 |
| 125.x PRC not in position | UC3 |
| 126.x Conveyor 3 bottom disengaged | UC3 |
| 127.x Plunger: fault | UC3 |
| 128.x Unable to eject can body | UC3 |
| 129.x Inadequate suction | UC3 |
| 131.x Trailing end too early | UC3 |
| 132.x Trailing end too late | UC3 |
| 139.x Suction hood not in position | UC3 |
| 141.x Machine clock lost | UC3 |
| 142.x Protective door: open | UC3 |
| 147.x STW: sheet guide 5 is open | UC3 |
| 148.x STW: sheet guide 6 is open | UC3 |
| 149.x STW: sheet guide 7 is open | UC3 |
| 152.x Lacquer: initial fill timeout exceeded | UC3 |
| 153.x Basin not filled | UC3 |
| 154.x Basin: insufficient lacquer flow | UC3 |
| 156.x STW: transport conveyor scoring station open | UC3 |
| 157.x STW: acceleration conveyor is open | UC3 |
| 158.x STW: sheet reject is defective | UC3 |
| 160.x Conveyor 2: clutch disengaged | UC3 |
| 164.x STW: Protective door right open | UC3 |
| 165.x STW: Protective door left open | UC3 |
| 167.x STW: tongue wheel not in position / tongue wheel upper position | UC3 |
| 168.x STW: tongue wheel locked | UC3 |
| 172.x STW: Sheet guide 1/2 is open | UC3 |
| 173.x STW: Sheet guide 2 is open | UC3 |
| 175.x STW: Sheet guide 3 is open | UC3 |
| 176.x Double sheet detected | UC3 |
| 183.x Protective door: welding transformer open | UC3 |
| 185.x EMERGENCY STOP: Machine | UC3 |
| 188.x STW: Sheet guide 4 is open | UC3 |
| 190.x Too many deflected sheets | UC3 |
| 193.x Feeder overload | UC3 |
| 194.x Sheet missing in rollformer | UC3 |
| 195.x Oil level too low | UC3 |
| 197.x Protective door: welding rollers open | UC3 |
| 199.x EMERGENCY STOP: line | UC3 |
| 200.x Unisoud/Pulsar: Measured current regulator deviation | UC3 |
| 202.x Double sheet deflector is defective | UC3 |
| 204.x First can-body contaminated | UC3 |
| 205.x Protective door: wire loop open | UC3 |
| 240.x Sensor defective | UC3 |
| 240.x Sensor defective | UC3 |
| 240.4 Sensor defective | UC3 |
| 240.5 Sensor defective | UC3 |
| 240.6 Sensor defective | UC3 |
| 240.12 Sensor defective | UC3 |
| 240.12 Sensor defective | UC3 |
| 240.13 Sensor defective | UC3 |
| 240.13 Sensor defective | UC3 |
| 240.14 Sensor defective | UC3 |
| 240.19 Sensor defective | UC3 |
| 240.25 Sensor defective | UC3 |
| 240.25 Sensor defective | UC3 |
| 240.32 Sensor defective | UC3 |
| 240.32 Sensor defective | UC3 |
| 240.33 Sensor defective | UC3 |
| 240.33 Sensor defective | UC3 |
| 252.x Setting of key switches inadmissible | UC3 |
| 252.x Selection of Mode/Function are invalid | UC3 |
| 300.x Safety relay monitoring | UC3 |
| 305.x Bad weld profilee | UC3 |
| 306.x Weld profile too complex | UC3 |
| 308.x Monitor Channel failed | UC3 |
| 313.x Too many missing can-bodies | UC3 |
| 314.x Too many can-bodies on ejector conveyor | UC3 |
| 320.x Setup successful | UC3 |
| 327.x Can-body jam | UC3 |
| 329.x Sheet missing in rollformer | UC3 |
| 330.x Double-sheet: sensor voltage | UC3 |
| 334.x Setup is required | UC3 |
| 337.x Monitor: no limits available | UC3 |
| 340.x Monitor: invalid setup data | UC3 |
| 341.x Setup is requirede | UC3 |
| 342.x Monitor: speed changed | UC3 |
| 343.x Monitor: Machine clock has changed | UC3 |
| 344.x Monitor: defective hardware | UC3 |
| 345.x Analog board defective | UC3 |
| 347.x Stationary transport / Sensor defective | UC3 |
| 354.x Outside seam coating system is not ready | UC3 |
| 355.x Inside seam coating or powder system is not ready | UC3 |
| 361.x Insufficient powder level | UC3 |
| 363.x Oven is not ready | UC3 |
| 365.x Powder test mode is on | UC3 |
| 366.x Can-body jam | UC3 |
| 367.x EAC/DCS can-body jam | UC3 |
| 368.x Elevator/Erector fault | UC3 |
| 370.x Vacuum not released | UC3 |
| 374.x LARC: conveyor stopped too early | UC3 |
| 376.x Combustion air pressure too low | UC3 |
| 377.x Process air pressure too low | UC3 |
| 378.x Motor too hot | UC3 |
| 378.x Servo amplifier too hot | UC3 |
| 379.x Loader is above top | UC3 |
| 381.x External machine stop | UC3 |
| 414.x Powder: RS232 communication fault | UC3 |
| 415.x Powder: incorrect firmware version | UC3 |
| 417.x Powder monitor: signal too high | UC3 |
| 418.x Powder monitor: Sensor or background contaminated | UC3 |
| 419.x Powder monitor: signal too low | UC3 |
| 420.x Powder monitor: machine clock unstable | UC3 |
| 498.x 24V power supply fault | UC3 |
| 421.x Powder: insufficient startup voltage | UC3 |
| 422.x Powder: insufficient startup current | UC3 |
| 423.x Powder: Measured current out of working range | UC3 |
| 424.x Powder monitor: Wrong reference data | UC3 |
| 426.x SOUVIS: Not responding | UC3 |
| 444.x SOUVIS: No confirmation | UC3 |
| 479.x Suction unit not ready | UC3 |
| 498.x 24V power supply fault | UC3 |
| 491.x Shuttle 1: rear end position | UC3 |
| 493.x Shuttle 1: front end position | UC3 |
| 497.x Overcurrent release | UC3 |
| 500.x Line: Control cabinet too hot | UC3 |
| 507.x Compressed air too low / outside pressure range | UC3 |
| 521.x Drive fault / overcurrent release | UC3 |
| 526.x Battery backup check: | UC3 |
| 545.x Wire break at profiler | UC3 |
| 547.x CamProfile Download in Progress | UC3 |
| 548.x Powder monitor: bad status | UC3 |
| 549.x Powder: bad packet status | UC3 |
| 550.x Powder: bad read access | UC3 |
| 551.x Powder: bad data access | UC3 |
| 559.x Waiting for Press | UC3 |
| 565.x Sheet Stack not in Position | UC3 |
| 566.x Powder monitor: reference reflector not applied | UC3 |
| 567.x Powder monitor: calibration required | UC3 |
| 572.x Powder: firmware not loaded | UC3 |
| 574.x Powder: download in progress | UC3 |
| 575.x Move loader to bottom position | UC3 |
| 576.x Pack aligner not at back position | UC3 |
| 577.x Pack not aligned | UC3 |
| 579.x Pack feeder protective door open | UC3 |
| 581.x SOUVIS | UC3 |
| 582.x Inside spray: lacquer flow not ok | UC3 |
| 584.x Sensor defective | UC3 |
| 587.x Drive fault | UC3 |
| 588.x Analog values too small | UC3 |
| 589.x Min. sheet stack | UC3 |
| 590.x Energy channel is switched off | UC3 |
| 591.x No analog signal from OCR unit | UC3 |
| 596.x Line: Turn table inlet conveyor has stopped | UC3 |
| 597.x Line: Can jam on erector | UC3 |
| 598.x Line: Can jam on turner | UC3 |
| 600.x Electromagnetic disturbance | UC3 |
| 604.x Line: In manual mode | UC3 |
| 605.x All can bodies ejected | UC3 |
| 606.x DC Fuse broken | UC3 |
| 606.x DC voltage asymmetric | UC3 |
| 606.x DC voltage shorted | UC3 |
| 606.x DC voltage too high | UC3 |
| 606.x DC voltage too low | UC3 |
| 606.x Dig.Outp.X8 overcurrent | UC3 |
| 606.x Driver board1 not found | UC3 |
| 606.x Driver board2 not found | UC3 |
| 606.x Driver board3 not found | UC3 |
| 606.x Driver board4 not found | UC3 |
| 606.x Gap too small | UC3 |
| 606.x Host read > | UC3 |
| 606.x Host write > | UC3 |
| 606.x I2C > | UC3 |
| 606.x Initialisation lost | UC3 |
| 606.x Main contactor remains off | UC3 |
| 606.x Main contactor remains on | UC3 |
| 606.x Main voltage too high | UC3 |
| 606.x Main voltage too low | UC3 |
| 606.x No Regulator Identification | UC3 |
| 606.x Parameter limitation | UC3 |
| 606.x Relay driver X9 > | UC3 |
| 606.x SPI > | UC3 |
| 606.x Unit1 IGBT HBA shorted | UC3 |
| 606.x Unit1 IGBT HBB shorted | UC3 |
| 606.x Unit1 Overcurrent | UC3 |
| 606.x Unit2 IGBT HBA shorted | UC3 |
| 606.x Unit2 IGBT HBB shorted | UC3 |
| 606.x Unit2 Overcurrent | UC3 |
| 606.x Unit2 Rms Current Deviation | UC3 |
| 606.x Unit3 IGBT HBA shorted | UC3 |
| 606.x Unit3 IGBT HBB shorted | UC3 |
| 606.x Unit3 Overcurrent | UC3 |
| 606.x Unit3 Rms Current Deviation | UC3 |
| 606.x Unit4 IGBT HBA shorted | UC3 |
| 606.x Unit4 IGBT HBB shorted | UC3 |
| 606.x Unit4 Overcurrent | UC3 |
| 606.x Unit4 Rms Current Deviation | UC3 |
| 606.x Weld Synchronization missing | UC3 |
| 607.x Unit1 Fan not running | UC3 |
| 607.x Unit1 IGBT too hot | UC3 |
| 607.x Unit1 too hot | UC3 |
| 607.x Unit2 IGBT too hot | UC3 |
| 607.x Unit2 too hot | UC3 |
| 607.x Unit3 IGBT too hot | UC3 |
| 607.x Unit3 too hot | UC3 |
| 607.x Unit4 IGBT too hot | UC3 |
| 607.x Unit4 too hot | UC3 |
| 607.x Unit2 Fan not running | UC3 |
| 607.x Unit3 Fan not running | UC3 |
| 607.x Unit4 Fan not running | UC3 |
| 608.x SOUVIS | UC3 |
| 609.x Machine clock lost | UC3 |
| 612.x Protective door: feeder open | UC3 |
| 613.x Roller head not lifted | UC3 |
| 618.x Grease level too low | UC3 |
| 619.x Handwheel engaged | UC3 |
| 620.x Positioning pin inserted | UC3 |
| 621.x Feeder magazine open | UC3 |
| 622.x Scoring station open | UC3 |
| 623.x Sucker rod disengaged | UC3 |
| 624.x Rollformer safety clutch | UC3 |
| 625.x Air pressure guiding tool too low | UC3 |
| 626.x Ejector: Twin can detected | UC3 |
| 627.x Feeder: vacuum off delay too long | UC3 |
| 628.x Monitor: First can travelling time out of tolerance | UC3 |
| 629.x Pulsar: Contamination detected | UC3 |
| 606.x Bad weld profile | UC3 |
| 606.x 24V_BLK1 X9 missing | UC3 |
| 606.x Contamination | UC3 |
| 630.x Brake > | UC3 |
| 630.x Clutch disengaged | UC3 |
| 630.x Clutch not engaged | UC3 |
| 630.x Clutch not released | UC3 |
| 630.x Communication | UC3 |
| 630.x DC voltage too low | UC3 |
| 630.x Drive defective | UC3 |
| 630.x Drive missing | UC3 |
| 630.x Drive overloaded | UC3 |
| 630.x Resolver | UC3 |
| 630.x Hardware enable missing | UC3 |
| 630.x Motor defective / wiring wrong | UC3 |
| 630.x Not in position | UC3 |
| 630.x Output overload | UC3 |
| 630.x Position > too large | UC3 |
| 630.x Position Limit reached | UC3 |
| 630.x Power Input out of tolerance | UC3 |
| 630.x Encoder | UC3 |
| 630.x Unknown > | UC3 |
| 630.x System > | UC3 |
| 630.x Sensors/limit switch | UC3 |
| 630.x Power supply fault | UC3 |
| 630.x Sensor defective | UC3 |
| 630.x Usage > | UC3 |
| 630.x Wire loop too short | UC3 |
| 630.x Wire break | UC3 |
| 631.x Motor too hot | UC3 |
| 631.x Servo amplifier too hot | UC3 |
| 631.x Wire traction unstable | UC3 |
| 632.x Function affected by contamination | UC3 |
| 636.x Can-body jam | UC3 |
| 637.x Line: Downstream/Bodyformer has stopped | UC3 |
| 638.x Transport 1 clamp open | UC3 |
| 639.x STW: tongue rejection failed | UC3 |
| 647.x Deviation too large | UC3 |
| 647.x Deviation zero | UC3 |
| 647.x Inductance too large | UC3 |
| 647.x No results | UC3 |
| 647.x Weld circuit open | UC3 |
| 648.x STW: Too many missing tongues | UC3 |
| 655.x Software too old | UC3 |
| 657.x Move loader to bottom position | UC3 |
| 660.x Blank stack robot above rollformer | UC3 |
| 661.x Sensor defective | UC3 |
| 662.x Outside spray: Insufficient lacquer flow | UC3 |
| 663.x ARS/SRM: Out of Measuring Range | UC3 |
| 664.x Oven not heat up | UC3 |
| 665.x ARS/SRM: Measuring plate shorted | UC3 |
| 666.x Monitor: Too many measured samples during setup | UC3 |
| 667.x Protective door/Emergency Stop monitoring fault | UC3 |
| 668.x Protective door: rollformer open | UC3 |
| 668.x Protective door: can guide channel is open | UC3 |
| 668.x Protective door: can guide channel is open | UC3 |
| 668.x Protective door: rollformer open | UC3 |
| 670.x Sorter: Tube is missing at end of transout | UC3 |
| 671.x Powder monitor: Calibration out of tolerance | UC3 |
| 672.x Can-body height | UC3 |
| 673.x Eject station: Unstable can detection | UC3 |
| 677.x Sheet Stack not in Position | UC3 |
| 679.x Transport1 brake is active | UC3 |
| 680.x Plate roll at weld station is blocked | UC3 |
| 681.x Output overload | UC3 |
| 681.x Overtemperature: Inductor 1 | UC3 |
| 681.x Overtemperature: Inductor 2 | UC3 |
| 681.x System > | UC3 |
| 681.x Internal supply | UC3 |
| 681.x DC voltage too low | UC3 |
| 681.x Overtemperature: Generator | UC3 |
| 681.x Fan failure | UC3 |
| 681.x Electromagnetic disturbance | UC3 |
| 681.x General fault | UC3 |
| 681.x Analog values too large | UC3 |
| 681.x Overvoltage | UC3 |
| 681.x current regulator failure | UC3 |
| 681.x Overcurrent | UC3 |
| 681.x Hardware enable missing | UC3 |
| 681.x short-circuit | UC3 |
| 681.x Current out of Tolerance | UC3 |
| 682.x Rounding speed has changed | UC3 |
| 683.x Pulsar: Power supply switch on timeout | UC3 |
| 685.x Acopos drive enable missing | UC3 |
| 686.x Seam cooling unit not ready | UC3 |
| 687.x conveyor 3 bottom | UC3 |
| 688.x Two hand button activation: operation failed | UC3 |
| 689.x Feeder: Too many sheets out of timing tolerance | UC3 |
| 690.x Output: powered with external voltage | UC3 |
| 691.x Powder: CPF silo sensor contaminated | UC3 |
| 692.x Power supply missing | UC3 |
| 693.x Power supply jumper wrong | UC3 |
| 694.x Node hardware defective | UC3 |
| 695.x Energy channel is switched off | UC3 |
| 696.x Energy: quality factor | UC3 |
| 697.x Eject all is ON (Push button) | UC3 |
| 698.x Can-body jam | UC3 |
| 699.x Output overload | UC3 |
| 699.x Overtemperature: Inductor 1 | UC3 |
| 699.x Overtemperature: Inductor 2 | UC3 |
| 699.x System > | UC3 |
| 699.x Internal supply | UC3 |
| 699.x DC voltage too low | UC3 |
| 699.x Overtemperature: Generator | UC3 |
| 699.x Fan failure | UC3 |
| 699.x Electromagnetic disturbance | UC3 |
| 699.x General fault | UC3 |
| 699.x Analog values too large | UC3 |
| 699.x Overvoltage | UC3 |
| 699.x current regulator failure | UC3 |
| 699.x Overcurrent | UC3 |
| 699.x Hardware enable missing | UC3 |
| 699.x short-circuit | UC3 |
| 699.x Current out of Tolerance | UC3 |
| 700.x No signal from Encoder | UC3 |
| 701.x Line control : Linestop to welder | UC3 |
| 702.x Bodyformer: Welder off | UC3 |
| 703.x Oven: SCU not ready | UC3 |
| 704.x Inside: lacquer system fault | UC3 |
| 705.x Unisoud/Pulsar: Measured current regulator deviation | UC3 |
| 734.x Heat: Pyrometer is not ready | UC3 |
| 742.x Guidance not closed | UC3 |
| 743.x Rollformer open/close: Mechanically locked | UC3 |
| 744.x Rollformer open/close: Protective door fault | UC3 |
| 745.x Machine stop extern (energy free) | UC3 |
| 746.x Machine stop (energy free) | UC3 |
| 748.x One hand (slow motion): operator failed | UC3 |
| 749.x Light barrier interrupted | UC3 |
| 750.x Sensor contaminated | UC3 |
| 751.x Sensor defective | UC3 |
| 752.x Sensor defective | UC3 |
| 753.x Cooling water | UC3 |
| 754.x Cooling water / DISCON too hot | UC3 |
| 755.x Air pressure is too high | UC3 |
| 756.x Lacquer monitor is activated | UC3 |
| 757.x Wire knot monitoring | UC3 |
| 758.x Wire magazine is empty | UC3 |
| 759.x Wrong Hardware | UC3 |
| 760.x Contamination | UC3 |
| 761.x Pressure out of tolerance | UC3 |
| 763.x CANopen: Bus off | UC3 |
| 764.x Device missing | UC3 |
| 765.x Drive system startup is in progress | UC3 |
| 766.x Too many deflected sheets | UC3 |
| 767.x Insufficient powder level | UC3 |
| 768.x Line stop | UC3 |
| 769.x Energy: Short circuit voltage too low | UC3 |
| 770.x Pressure out of tolerance | UC3 |
| 771.x Can-body guide channel is not at down position | UC3 |
| 772.x Outside spray: System not in working position | UC3 |
| 773.x Emergency: Feedback loop faulty | UC3 |
| 774.x PNOZ: Fatal > | UC3 |
| 782.x System is mandatory | UC3 |
| 783.x Line: Turner outlet jam | UC3 |
| 784.x Upender can jam | UC3 |
| 785.x PRC: Lacquer level is too low | UC3 |
| 786.x Powder: No response | UC3 |
| 787.x Machine clock unstable | UC3 |
| 789.x Powder: HVS current too low: wiring fault | UC3 |
| 790.x Powder: fault | UC3 |
| 792.x Overtemperature switch | UC3 |
| 793.x Protective door: water plate open | UC3 |
| 794.x CAN Bus > | UC3 |
| 794.x CAN High > | UC3 |
| 794.x CAN Low > | UC3 |
| 794.x Resistance too high | UC3 |
| 794.x Resistance too low | UC3 |
| 794.x Not allowed on this node | UC3 |
| 794.x Device defective | UC3 |
| 794.x Measurement > | UC3 |
| 796.x PRC: Lacquer level is low | UC3 |
| 797.x Flow rate too low | UC3 |
| 798.x Press oven on button to restart burner ignition | UC3 |
| 799.x Burner control must be reset manually | UC3 |
| 800.x Oven: Safety combination | UC3 |
| 801.x Suction hood not in position | UC3 |
| 802.x Destacker: Double sheet not ejected | UC3 |
| 803.x Destacker: Additional sheet detected | UC3 |
| 804.x Destacker: Sheet transport fault | UC3 |
| 805.x STW: sheet reject is defective | UC3 |
| 806.x Communication | UC3 |
| 806.x Drive defective | UC3 |
| 806.x Measurement > | UC3 |
| 806.x Width not constant | UC3 |
| 806.x Width too large | UC3 |
| 806.x Width too small | UC3 |
| 807.x Line stop | UC3 |
| 810.x OSS: Lacquer pressure out of tolerance | UC3 |
| 815.x Contamination | UC3 |
| 817.x Can-body jam | UC3 |
| 818.x Double-sheet container is full | UC3 |
| 819.x STW Monitor: Too many bad tongue welding cycles. | UC3 |
| 820.x Burner control could not be reset | UC3 |
| 821.x Sensor defective | UC3 |
| 822.x Protective door: Manual feed open / not locked | UC3 |
| 823.x Pack transfer TP not in safe position | UC3 |
| 824.x Protective door: Front open / Front left open | UC3 |
| 825.x Protective door: Front right open | UC3 |
| 826.x Protective door: Feeder right down open / not locked | UC3 |
| 827.x Protective door: Feeder right up open / not locked | UC3 |
| 828.x Protective door: Feeder backside open / not locked | UC3 |
| 829.x UTC lacquer reservoir empty | UC3 |
| 830.x UTC lacquer reservoir is filling | UC3 |
| 834.x Lift table: Palett/Pack incorrect loaded | UC3 |
| 835.x TP: Rear cover open / not locked | UC3 |
| 836.x TP: Right cover open / not locked | UC3 |
| 837.x UTC change empty lacquer tank | UC3 |
| 838.x Monitor: Input signal out of range | UC3 |
| 839.x Welder run with batch counter only / Set batch counter! | UC3 |
| 840.x TP: Rear cover open / not locked | UC3 |
| 841.x Monitor: Eject logic not started | UC3 |
| 842.x Line stop | UC3 |
| 844.x Protective door: Rear open or not acknowledged | UC3 |
| 845.x Protective door: Rear up open | UC3 |
| 846.x Loader is above top | UC3 |
| 847.x EMERGENCY STOP: Whole line | UC3 |
| 848.x EMERGENCY STOP: External | UC3 |
| 853.x Discon pump switch off: Circuit 2 too low | UC3 |
| 854.x Oven: Wait for burner power supply | UC3 |
| 855.x Line control : Linestop to welder | UC3 |
| 856.x Flow rate too low / Water pump switched off | UC3 |
| 857.x Protective door: Manual feed open / not locked | UC3 |
| 858.x MLC: Downstream demands immediate stop | UC3 |
| 859.x MLC: Communication to line control missing | UC3 |
| 859.x MLC: Communication to line control missing | UC3 |
| 860.x MLC: Communication to line control missing | UC3 |
| 861.x TP: Rear cover open / not locked | UC3 |
| 862.x TP: Rear cover open / not locked | UC3 |
| 863.x TP: Right cover open / not locked | UC3 |
| 864.x Protective door: Manual feed open / not locked | UC3 |
| 865.x Energy: Measured current too low | UC3 |
| 866.x ARS/SRM: Piezo position out of tolerance | UC3 |
| 867.x MLC: Downstream not ready | UC3 |
| 871.x Erector DCU: Magnet off time between cans too short | UC3 |
| 872.x Erector DCU: Magnet driver fault | UC3 |
| 873.x MLC: Communication to line control missing | UC3 |
| 874.x Oven not operational | UC3 |
| 875.x Lacquer temperature out of tolerance | UC3 |
| 876.x RS 232 communication fault | UC3 |
| 877.x No power for peltier element | UC3 |
| 878.x User interface is locked | UC3 |
| 881.x Pulsar: Too many contamination on short circuit | UC3 |
| 883.x UTC lacquer reservoir empty | UC3 |
| 884.x LTC Device status > | UC3 |
| 885.x MLC: Downstream not ready | UC3 |
| 886.x LTC maximum temperature exceeded. Check LTC cooling! | UC3 |
| 887.x STW: Wire threading switch is enabled | UC3 |
| 888.x Oven: Pyrometer temperature too low | UC3 |
| 889.x Oven: Pyrometer temperature too low | UC3 |
| 890.x Oven: Pyrometer not working | UC3 |
| 891.x Upstream system clutch disengaged | UC3 |
| 892.x Machine safety stop | UC3 |
| 893.x Peltier element defective or wiring fault | UC3 |
| 894.x Machine off | UC3 |
| 895.x Lacquer monitor: pulse duration too small | UC3 |
| 896.x Lacquer monitor: pulse duration too small | UC3 |
| 897.x Oven: Can flow monitoring entry to exit fault | UC3 |
| 898.x Can body was not ejected / diverted | UC3 |
| 899.x Stationary transport / Sensor defective | UC3 |
| 900.x Sensor defective | UC3 |
| 902.x HvGenerator | UC3 |
| 902.x Voltage too high | UC3 |
| 902.x Current too high | UC3 |
| 902.x Current too low | UC3 |
| 902.x Current out of range | UC3 |
| 902.x Resistance too high | UC3 |
| 902.x Resistance too low | UC3 |
| 902.x Lifesign > | UC3 |
| 902.x Internal fault | UC3 |
| 902.x Serial communication timeout | UC3 |
| 902.x Wiring fault | UC3 |
| 902.x Power supply missing | UC3 |
| 902.x Output current too low | UC3 |
| 902.x SPI > | UC3 |
| 902.x Signal invalid | UC3 |
| 902.x Voltage too low | UC3 |
| 902.x General fault | UC3 |
| 903.x Test pulse > | UC3 |
| 903.x Time discrepancy channel 2 | UC3 |
| 903.x Time discrepancy channel 1 | UC3 |
| 903.x Time discrepancy releasing | UC3 |
| 903.x Short/cross circuit | UC3 |
| 903.x Lock > | UC3 |
| 903.x Release > | UC3 |
| 903.x Hardware > | UC3 |
| 903.x Release > 2 | UC3 |
| 904.x Safety not ready | UC3 |
| 905.x Powder application in cleaning process | UC3 |
| 908.x Zero position not found | UC3 |
| 910.x Loader: Sheet stack is empty | UC3 |
| 913.x Monitor: Feeder ON signal unstable | UC3 |
| 917.x Too many rejected can-bodies | UC3 |
| 918.x Oven eject container at oven end is full | UC3 |
| 919.x Oven target status | UC3 |
| 920.x Upender: Downline not ready | UC3 |
| 921.x OHC is open | UC3 |
| 922.x HvDiagnostics | UC3 |
| 924.x Energy counter not working | UC3 |
| | |
| | |
